WAGO

Connecting low voltage wires together is a common task when working with lighting systems like festoon cables, LED drivers, dotless strips, modules, flexible neon, and more. Follow this detailed guide to ensure safe and reliable connections for your low voltage lighting projects.

Materials You Will Need:

• Low voltage wires (such as festoon cable, dotless strip wires, module wires, or flexible neon wires).
• Wire cutters/strippers.
• Soldering iron and solder (for permanent connections, if needed).
• Heat shrink tubing (for added insulation and protection).
• Wire connectors (such as wire nuts, butt connectors, or crimp connectors).
• Electrical tape (as an alternative to heat shrink tubing).
• Cable ties (for cable management).
• Heat gun or lighter (if using heat shrink tubing).
• Safety gear: Safety goggles and heat-resistant gloves.

Procedure:

1. Safety First:

• Always work in a well-ventilated area.
• Wear safety goggles and heat-resistant gloves to protect your eyes and hands.

2. Prepare the Wires:

• Ensure that the low voltage wires you plan to connect are clean, undamaged, and stripped of any damaged insulation.
• Strip the ends of the wires to expose approximately 1/4 to 1/2 inch (6-12 mm) of bare wire. Use wire strippers to do this.

3. Choose the Connection Method:

Wire Connectors (WAGO):

• Wire connectors are a quick and reliable way to connect low voltage wires together. They come in various sizes to accommodate different wire gauges.
• To use wire connectors:
  • Insert the prepared wires into the open slots of the WAGO connector. Make sure that each wire goes into its designated slot based on size and polarity.
  • Once the wires are inserted correctly, close the clamping unit securely. This action will grip the wires tightly, establishing a secure connection.
  • Ensure that the wires are held firmly in place by gently tugging on them.

Soldering (for Permanent Connections):

• Soldering provides a strong and secure connection. This method is ideal for applications where you don't want any chance of wires coming loose.
• To solder wires together:
  • Twist the exposed ends of the wires together.
  • Heat your soldering iron to the appropriate temperature for your solder.
  • Apply the soldering iron to the twisted wires to heat them.
  • Apply solder to the heated wires, allowing it to flow evenly over the twisted area.
  • Remove the soldering iron and let the solder cool and solidify. Ensure the wires are held in place until the solder hardens.
  • Optionally, slide heat shrink tubing over the soldered area and use a heat gun or lighter to shrink it for added protection.

4. Insulate the Connection:

• If using wire connectors, they provide built-in insulation.
• If soldering, slide heat shrink tubing over the soldered area or use electrical tape to insulate the connection.
• If using heat shrink tubing, apply heat evenly using a heat gun or lighter until the tubing shrinks and seals the connection tightly. Ensure there are no gaps in the tubing.

5. Secure and Organise the Wires:

• Use cable ties or clips to secure and organise the connected wires, keeping them neat and tidy.

6. Test the Connection:

• Before energising your lighting system, test the connection to ensure it's secure and functioning correctly.

7. Repeat as Needed:

• Repeat the above steps for all the low voltage wire connections in your project.

By following these steps, you can safely and effectively connect low voltage wires for your festoon cables, dotless strips, modules, flexible neon, and other low voltage lighting applications. Always adhere to safety guidelines and manufacturer recommendations for your specific lighting products.

Whether you're working on electrical projects or crafting intricate setups, knowing how to properly connect wires is essential for safety and efficiency. In this detailed guide, we'll walk you through two common methods: soldering and using Wago connectors. We'll also emphasise the importance of maintaining consistent wire polarity to ensure your connections work seamlessly.

Materials You'll Need:

• Wires to be connected
• Soldering iron and solder (if soldering)
• Wago connectors (if using)
• Wire stripper or cutter
• Dual Adhesive Heat shrink tubing (if soldering)
• Electrical tape (if using)
• Multimeter (for polarity verification)

Method 1: Soldering Wires

Step 1: Prepare the Wires

1. Strip about 1 cm of insulation from each wire using a wire stripper.
2. Twist the exposed wire strands to prevent fraying.
3. For safety, we recommend the wires are feathered to ensure the opposing wires do not touch.

Step 2: Solder the Wires

1. Heat your soldering iron and apply a small amount of solder to the tip.
2. Hold the wires together with their stripped ends aligned.
3. Touch the soldering iron's tip to the wires, allowing the heat to melt the solder and create a strong bond between the wires.

Step 3: Insulate with Heat Shrink Tubing (This step can be done before step 2 to make a more streamlined connection)

1. Slide a piece of heat shrink tubing over the soldered area.
2. Use a heat gun to shrink the tubing, providing insulation and protection to the solder joint.

Method 2: Using Wago Connectors

Step 1: Prepare the Wires

1. Strip about 1 cm of insulation from each wire.
2. Insert the stripped wires into the appropriate Wago connector slots (same polarities). Ensure each wire is securely inserted.

Step 2: Secure the Wires

1. Press down on the orange lever of the Wago connector. This will securely clamp the wires in place.

Step 3: Verify Polarity

1. Use a multimeter to verify that the wire polarity is consistent between the connections.
2. Connect the multimeter probes to the corresponding wires to ensure positive (+) and negative (-) match.

General Tips:

• Weatherproofing: Employing electrical tape is an effective method for swiftly safeguarding your connection against environmental factors. Exercise caution, as any openings can pose potential hazards.

• Maintain Consistent Polarity: To prevent electrical issues, ensure that the wires' polarity (positive and negative) matches correctly when connecting them. A reversed polarity can lead to equipment damage or malfunction.

• Safety First: Always work in a well-ventilated area, and take necessary precautions to avoid burns when soldering. If using Wago connectors, handle them carefully to prevent any accidental damage.

• Practice Good Wire Management: Keep the wire connections tidy by using cable ties, conduit, or other wire management solutions.

• Test Your Connections: Before finalising your project, test the connected wires using appropriate electrical equipment to verify that the connections are functioning as intended.

• Wear Safety Gear: When soldering, protect your hands with gloves and your eyes with safety goggles to prevent accidental burns or splashes.

By following this guide, you'll be able to confidently and safely connect wires using both soldering and Wago connectors while maintaining proper polarity. This skill will prove invaluable for a wide range of electrical and DIY projects.